Refrigeration Package Systems

EUROMON
The package-system refrigeration line EUROMON is composed of 7 models from 800 to 4400 W in the positive and 5 models from 600 to 3000 W in the negative range.

This compact unit is fast and easy to install thanks to the products which have been assembled, tested and adjusted in the factory.

SMALL COLD ROOM SPECIAL OFFER
We have put together a package ideal for anyone needing a small cold room system.

The real technical advantages offered by the new generation of monoblock EUROMON refrigeration units have earned them a place as a leader in their market:

FAST INSTALLATION: The installation method adopted for this unit is extremely simple, All that is required to fasten the monoblock unit is two notches at the top of the cold storage room, Once in place, the unit is ready for use immediately by simply plugging it into the mains power supply. Furthermore, the various control parameters are factory-set according to the pre-defined application.
TOTAL ACCESSIBILITY:The front cover is composed of two parts to render access to internal elements of the condensing unit, in particular the compressor, condenser fans and re-evaporation heaters easier. The regulator is equipped with a plug-in terminal rail to simplify maintenance work.
POWER SAVING: The unit cooler electrical defrost mode is approximately three times more economical than the hot gas defrost system in terms of power consumption. Furthermore, it is independent of compressor operation which extends the operating life of this element.
EVAPORATION OF CONDENSATION: This function is assured by a drain pan containing an immersion heater which, contrary to the discharge gas solution, does not require the compressor and protects the piping from corrosion. Power consumption is minimised by the self-adapting faculty of the heater.
OPTIMUM ROOM SPACE: The 'ceiling unit' design form of the unit cooler ensures not only better air dispersion but also provides more storage space inside the cold storage room.

To get the technical specification on the Euromon - Click HERE (right click and select Save Target As)

MINIFJORD

The MINIFJORD low capacity, split system range with 6 positive models and 3 negative models, covers the cooling requirements for cold rooms from 3 to 110 m3.

CONDENSING UNIT
• Frame and casing made of pre-lacquered metal sheet for an outdoor application (on a wall or on the ground).
• HP pressure switch for MIF P 7A and MIF N 14A.
• Copper/aluminium condenser coil with 230 V single-phase or 400 V 3- phase fan - 1,500 r.p.m.
• Liquid line with receiver-dryer and hygroscopic sight glass.
• Pump down regulation with LP pressure switch and solenoïd valve on MIF P 25A and MIF N 26A.
• Service valves (with 1/4 access valves) (inlet/outlet) outside the casing.
• Electrical box IP 537 with 1 electrical switchboard to standard CEI 439-1 and conform to APAVE requirements, passage of electrical cables via packing glands, pre-wired enclosure with plant and unit protection devices.
• Pre-filled with R404A.
• Circuit breaker and solenoid valve as standard for P 25A and N 26A models.

CONTROL
• Electronic regulation.
• Defrost control (air or electric).
• Lighting control.
• Display and transfer of alarms.
• An additional programmable contact (door open, person inside enclosure safety switch...).
• Built-in forced operation for fast cooling or freezing.

UNIT COOLER
• ABS material casing (up to MIF P 13A and MIF N 14A
models). Other units made of white painted steel sheet.
• Fin spacing 4.23 mm and copper/aluminium coil.
• Premounted large operating range expansion valve.
• Defrosting heater sensor (S2), and defrost termination.
• Pre-filled with Nitrogen.

To get the technical specification on the Minifjord - Click HERE (right click and select Save Target As)

If you need to download the FREE Acrobat Reader (version 6 - 8.6mb) -
click on this icon